Skip to main content
4.0.19 - Released October 21, 2024
- Access Points:
- BUGFIX: uninitialized WiFi client channel width value sent to cloud
- BUGFIX: interface race condition on boot up may leave radio disabled
- BUGFIX: captive portal: quickly alternating between radios leads to death'ed WiFi client
- BUGFIX: PAX1800v2: secondary Ethernet port status reported incorrectly
- Switches:
- remote syslog IP address not applied correctly
4.0.18 - Released September 09, 2024
- Access Points:
- BUGFIX: WiFi clients quickly alternating between radios leaves client unthrottled
- BUGFIX: captive portal: prevent crash on interface up & down
4.0.17 - Released July 22, 2024
- Access Points:
- BUGFIX: captive portal: RADIUS pre-auth of already connected WiFi clients on restart
- BUGFIX: PAX1800: slow DHCP delivery on SSID bridged with VLAN
- Switches:
- BUGFIX: network stack state machine loses track of long running permanent cloud connection
- BUGFIX: silence VMA open/close log messages
4.0.16 - Released May 29, 2024
- Access Points:
- BUGFIX: reg domain change after WiFi scan on AP without enabled SSIDs
- BUGFIX: PAX5400: improve WiFi performance by enabling WiFi offloading
- Switches:
- FEATURE: report port isolation status
4.0.15 - Released March 27, 2024
- Access Points:
- BUGFIX: captive portal: retain active wired client splash page session across reboot
- BUGFIX: captive portal: report WiFi band via Nas-Port-Id RADIUS field
- BUGFIX: syslog service not activated correctly
- BUGFIX: PA2200: race condition during post-flash checksum verification
4.0.14 - Released March 4, 2024
- Access Points:
- FEATURE: captive portal: hold excess auth request in waiting queue to reduce server load
- BUGFIX: captive portal: send client TX traffic stats via RADIUS OUTPUT fields
- BUGFIX: captive portal: send client RX traffic stats via RADIUS INPUT fields
- BUGFIX: PAX1800: ambient noise scan disabled due to reliability issues
4.0.13 - Released January 22, 2024
- Access Points:
- FEATURE: captive portal: report wired/wireless client type via RADIUS NAS-Port-Type attribute
- FEATURE: captive portal: report SSID ID or Ethernet port index via RADIUS NAS-Port attribute
- FEATURE: captive portal: report logout reason via RADIUS Acct-Terminate-Cause
- BUGFIX: PA1200: race condition during post-flash checksum verification
4.0.12 - Released December 12, 2023
- Switches:
- FEATURE: enable DHCP server search until VLAN init has been completed
- FEATURE: save port VLAN configuration across firmware upgrade
- FEATURE: per port isolation setting
4.0.11 - Released November 20, 2023
- Access Points:
- FEATURE: syslog HTTP SYN policy setting
- FEATURE: captive portal: report username via client splashpage status
- FEATURE: captive portal: obtain username during pre_auth response (if available)
- BUGFIX: captive portal: memory leak due to RADIUS async operations
4.0.10 - Released October 16, 2023
- Access Points:
- FEATURE: auto-recovery mode enable/disable config setting
- FEATURE: PAX5400: report upper & lower occupied frequency on 6GHz band
- BUGFIX: race condition with client throttling when more than one SSID bridged into VLAN
- BUGFIX: PAX5400: 6GHz channel 1 -33 not functioning in FCC domain
- BUGFIX: PA300/PA300E: WiFi may enter "deaf" mode after days of operation
4.0.9 - Released August 22, 2023
- Access Points:
- FEATURE: report WiFi client connected time
- FEATURE: report WiFi channel utilization (idle, busy, rx & tx)
- FEATURE: SSH ED25519 key authentication
- FEATURE: captive portal: monitor neigh cache to update internal IP address
- BUGFIX: captive portal: only resume pending RADIUS connections on shutdown
4.0.8 - Released July 28, 2023
- Access Points:
- FEATURE: captive portal: async RADIUS backend operations
- FEATURE: captive portal: trigger pre-auth call on wired MAC address detection
- FEATURE: captive portal: maintain keep alive status of wired clients via neigh cache
- FEATURE: captive portal: make RADIUS session id more unique by including device MAC and SSID identifier
- FEATURE: captive portal: apply per-client throttling limits to wired clients
- FEATURE: PAX5400: enable 2.4GHz & 5GHz beacon co-location support
- FEATURE: PAX5400: enable hunting-and-pecking loop and hash-to-element SAE PWE derivation on 6GHz
- BUGFIX: force WiFi scan channel dwelling time to 100ms
- BUGFIX: PA2200: unencrypted mesh reduces WiFi mesh to 11bg performance
- BUGFIX: PA1200: WiFi firmware crash due to nonLinearTxFir setting
4.0.7 - Released June 16, 2023
- Access Points:
- BUGFIX: DHCP request over mesh during boot phase not triggered
- BUGFIX: unencrypted mesh reduces WiFi mesh to 11bg performance
- BUGFIX: PAX5400: 6GHz demands OWE encryption on 'open' SSIDs
4.0.6 - Released June 1, 2023
- Access Points:
- BUGFIX: unable to stream live data via SSL/TLS
- BUGFIX: disable SSH client ED25519 support
- BUGFIX: captive portal: only block IPv6 forwarding on splashpage interfaces
- BUGFIX: PAX5400: channel selection with HT40+ channel with on 6GHz
- BUGFIX: PAX5400: hardware watchdog triggering reboot
4.0.5 - Released May 8, 2023
- Access Points:
- BUGFIX: race condition during mesh and SSID initialization on same band
- BUGFIX: 40MHz/80MHz/160MHz channel width setting with mesh and SSID on same band
- BUGFIX: PAX5400: LLDP announcement contain incorrect Ethernet port status
4.0.4 - Released March 16, 2023
- Access Points:
- FEATURE: WiFi 6 & WiFi 6E Mesh
- FEATURE: 160MHz channel width support
- FEATURE: WPA3 encryption (WPA2/WPA3 compatibility mode)
- FEATURE: PAX5400 platform support
- FEATURE: WiFi 6E band, client capability & usage reporting
- FEATURE: WiFi scan reports occupied frequencies
Comments
0 comments
Article is closed for comments.